Your Contact Person:  Marv Kreider Contact BUY AND REGISTER NOW

FAQ Hardware

ERROR Message: “D/A converter not detected” when starting or during  a session

Possible Problem:

  • Ensure your firmware is updated to the latest version. Go to Settings „About Tablet“  - Wireless Update and check for latest firmware update
  • 20 pin flat cable is not inserted fully into the tablet and/or the D/A Converter. Ensure the flat cable is fully inserted into the tablet and/or the D/A Converter so you won’t see any metal part of the connector.
  • aulty 20 pin flat cable that may cause intermittent connectivity issue. Contact your SBS service centre for further advice.

ERROR Message: “D/A Converter overheated”

  • The D/A Converter may be placed in an area that’s not well ventilated to allow sufficient dissipation of heat generated during the operation. Ensure that the cooling rips of the D/A Converter are not covered at all byany  material that may severely restrict the ventilation.
  • The D/A Converter temperature has reached its maximum threshold. Check the serial number of your converter (under „About application“). If the serial number is less than 1050, please contact your SBS service centre.

ERROR Message: “Applicator not detected”

Possible problem:

  • aulty applicator. Try to connect using a different applicator. If only one of the attached  applicator is not working, there is a high chance the applicator is faulty. Call your SBS service centre for further troubleshooting.
  • Connector not screwed in properly  to the D/A converter. Please check the connection.

How to check your D/A Convertor serial number

Go to iMRSone ->Settings ->About

da converter serial number

How to check the serial number of your tablet

Go to iMRSone -> Settings -> About

serial number tablet

Omnium1 tablet is not charging

In case of consistent or intermittent charging issues, please contact your SBS service centre.

Touch screen not responsive

The tablet is equipped with capacitive touch screen technology, which means that whenever one of your fingersgets in touch with the screen surface, it creates a tiny electrical disturbance that sends signals to the tablet. There are people who have problems operating a touch screen primarily due to their skin conductivity. Pressing hard on the screen won’t address the issue. One way to solve the issue is to use a capacitive stylus.

However, if you still are experiencing slow response even using a capacitive stylus, please contact SBS for further assistance.


Tablet seems to get sluggish and unstable. How to clean up?

Your Omnium1 tablet is built on Android Kit Kat 4.4.2 platform, and like any other rather sophisticated operating systems, over time it may get slowed down due to software application caching, temporary files, etc. created and left over during the usage or during improper shutdown and application crashes. Sometimes this even caused system instability, system refuses to boot-up properly (i.e. boot screen logo keep flashing up in a loop).

The easiest way to “clean-up” your system is by clearing your system cache partition without losing your existing data. Follow the steps below.

  1. Shutdown your tablet (or push the reset pin if tablet fails to shutdown or response)
  2. Press POWER and VOLUME (+) button at the same time to bring out the boot menu
  3. Use VOL (+) button to move selection to [Recovery Mode] and press VOL (-) to select
    clean up 01
  4. At the Android Mascott Screen, press POWER button once to bring up the next menu
    clean up 02
  5. Use VOL (-) button to move selection to [wipe cache partition] and then press VOL (+) once to select
    clean up 03

  6. Press VOL (+) to reboot your tablet

Tablet does not boot up, even when plugged into the wall

There are several possible problems:

  • Your tablet might be frozen. Insert a pin into the reset pinhole and reset the tablet.

pin reset

  • The wall adapter is faulty and fails to charge the tablet properly. Please contact your SBS service centre for further advice.

The tablet is getting warm/hot at the backside

Please ensure your firmware is updated to the latest version. If you have already updated to the latest firmware, then this may due to faulty 20 pin flat cable, D/A converter or tablet hardware issue. Please contact your nearest SBS service centre for further assistance.

Note: Avoid extreme bending of the 20 pin flat cable as this may damage the cable and cause a short circuit.


Replacing the battery?

The lifetime of the built in lithium battery pack is calculated with around 500 recharge cycles (depending on various circumstances). Over time the battery pack may need to be replaced. Please contact your SBS service centre for the replacement cost.

Replacing the screen?

Please contact your SBS service centre for the replacement cost and procedure.

SD Card reading error

The maximum micro-SD card size supported is 32GB.

If your SD Card is 32GB or less and still cannot be read by the tablet, reformat the SD Card with your PC or Mac (Fat 32, exFAT) as your current SD card format may not be recognized by the system or is corrupted.

Attention: All data will be erased.